automated tests - Jenkins 0 files published after build -


Text after "div class =" itemprop = "text">

I set up a Jenkins server with two jobs

The first job selection branch to develop and build the project On Jenkins's server again I have another job that chooses the production branch, it creates this branch on another Junkies slave which is a staging server. This work is configured so that on a successful creation it is on the production server Publishing artwork on SSH Hey there.

All SSH keys are setup and the scaffold connects to the server production server, but 0 files are transferred <89874cc01a9f669df69817b1049b1ab98ecb19d3 (original / output) SSH credentials Bitbucket Using GIT_SSH to install credentials using repo .gitcredentials> : Connecting to host [nginx-php-FastCGI] SSH: Connect with configuration [AmazonAWS] ... SSH: Disconnecting configuration [AmazonAWS] ... SSH: Locations 0 file (s) finished: success

to deploy Jenkins files

I checked scaffold workspace and files are being created, just do not send prod to the server. any suggestion ??

I have suggested that there is a separate exhaust prefix here and here I have suggestions As has been tried also tried a different exhaust prefix path

You / Remove

Edit:
Your source files can not be out of the job scope if your files are in the root of the workspace, then all To move the installation files, or to include the subdirectories to ** / * simply set it to * as it is all attached to it To do that, or else, a pattern relative to $ {WORKSPACE} .

Even a major / will not survive that specified workplace, in your case it will be $ {WORKSPACE} / var / www / workspace / opms- Staging-server . Even the parent directory ../ will not work as well. This is for security concerns, otherwise Joyconfigger can transfer personal files from Jenkins server.

If you need to obtain a file from another job, you will need to use the Copy artwork build step. Tell me that this is your case, and I will tell you further.

Comments

Post a Comment

Popular posts from this blog

Verilog Error: output or inout port "Q" must be connected to a structural net expression -

I get the error every time, I try to compile. I'm not sure why anyone can help is? I'm new to verilog. Module D_FF (clerk, d, reset_n, q); Input D, Clack, reset_en; Output Q; reg Q; lab4_gdl f1 (.lk (~ clk), d (d), .q.m (qm)); lab4_GDL f2 (.Clk (Clk), D (QM), .Q (Q)); Always start at @ (posedge clk, neggeous reset_n) (Reset_n == 0) Q & lt; = 0; Other questions & lt; = D; Edit End: The problem is what we are asking to do: In this section, you apply the memory / registration circuit on the AlterEdie 2 board. will do. The circuit has the following specifications: The present value of swift SW15-0 on the D2 board should be shown in four hexadecimal four sections of HEX3-0. This part of the circuit will be combination logic. To use an active-less asynchronous reset and KEY1 to use KEY0 as the clock input, you must store SW15-0in in a 16-bit register in the value The register should be enabled to have a 16-bit positive edge, which uses the embedded D flip-flo
Read more

jasper reports - How to center align barcode using jasperreports and barcode4j -

I use iReport 5.5.0 . How to align a barcode component to the center The relevant piece of my jrxml is below & Lt; JR: Code 128 xmlns: JR = "http://jasperreports.sourceforge.net/jasperreports/components" xsi: schemaLocation = "http://jasperreports.sourceforge.net/jasperreports/components http: //jasperreports.sourceforge Purge / xsd / components.xsd "textPosition =" bottom "& gt; & Lt; Jr: codeExpression & gt; & Lt; [CDATA [$ F {number}]] & gt; & Lt; / Jr: codeExpression & gt; & Lt; / Jr: Code 128 & gt; & Lt; / componentElement & gt; "Text" itemprop = "text"> Create a style after this, it is called "barcode", like: & lt; Style name = "barcode" fontName = "Helvetica" fONTSIZE = "10" hAlign = "center" valign = "center" /> and set the property of your barcode element to "barcode".
Read more

c# - ASP.NET MVC - Attaching an entity of type 'MODELNAME' failed because another entity of the same type already has the same primary key value -

In brief, the wrapper module is inserted during posting and the status of an entry is changed to 'modified' . Before changing the state, the state is set to 'separate', but calling attachments () causes the same error to be thrown away. I am using EF 6. Model / wrapper class public class avi model {public A is a {get; Set; } Public listing & lt; B & gt; B {received; Set; } Public cc {receipt; Set; }} Administrator edit public functioning (int? id) {if (id == null) {new HttpStatusCodeResult (HttpStatusCode.BadRequest); } If (! Conveyor Access (id.Value)) new HTTPTitus code result (HTTP status code. Forbidden); Var aViewModel = new AViewModel (); aViewModel.A = db.As.Find (id); If (aViewModel.Receipt == zero) {return HttpNotFound (); } aViewModel.b = db.Bs.Where (x => x.aid == id.Value) .Oolist (); AViewModel.Vendor = db.Cs.Where (x => x.cid == aViewModel.a.cID) .FirstOrDefault (); See Return (aViewModel); } [HTPFost] [Valid AntitiferousTeacon
Read more