debian - How do you install Libevent for PHP? -


मेरे डेबियन 7 64 बिट डेस्कटॉप पर libevent-dev लायब्रेरी स्थापित किया गया है:

$ sudo aptitude install -i libevent-dev

फिर मैंने पीईसीएल पुस्तकालय स्थापित किया है 

  $ pecl सूची स्थापित संकुल, चैनल pecl Php.net: ========================================= पैकेज संस्करण राज्य libevent 0.1 .0 बीटा   
 मैंने PHP और ओएस को पुनरारंभ कर दिया है लेकिन PHP एक लिखित एक्सचेंज के रूप में  phpinfo ()  के साथ libEvent की सूची नहीं है और मुझे  "PHP घातक त्रुटि: अपरिभाषित फ़ंक्शन event_base_new () को कॉल करें"  जब मैं इसका उपयोग करने का प्रयास करता हूं।  
 आप Libevent कैसे स्थापित करते हैं?   
 < div class = "post-text" itemprop = "text"> 
  PHP 5.X के लिए Libevent स्थापित करें   
  sudo apt-get install libevent-dev sudo Pecl स्थापित libevent-beta sudo su sudo echo 'extension = libevent.so' & gt; /etc/php5/mods-available/libevent.ini exit sudo ln -s /etc/php5/mods-available/libevent.ini/etc/php5/fpm/conf.d/ sudo ln -s / etc / php5 / mods -वेबल / libevent.ini /etc/php5/cli/conf.d/ सुडो सेवा php5-fpm restart   
  PHP 7.X के लिए Libevent स्थापित करें   
 
  
 
 
 
 
 
 
 
 
  
 
 इसे खोलें: / tmp / install_libevent  
  सीडी / tmp / install_libevent / pecl-event-libevent-master सूडो फ़ॉपीस सुडो। /configure   
 इस चरण के बाद हमारी कंसोल विंडो को स्क्रॉल करें और कोई चेतावनियाँ या त्रुटियों को खोजने का प्रयास करें मुझे एक चेतावनी मिली- re2c पैकेज को स्थापित करने के लिए जरूरी है।  
  sudo sudo sudo su sudo echo 'extension = libevent.so' & gt; /etc/php/7.0/mods-available/libevent.ini निकास sudo ln -s /etc/php/7.0/mods-available/libevent.ini/etc/php/7.0/fpm/conf.d/20-libevent। Ini sudo ln -s /etc/php/7.0/mods-available/libevent.ini/etc/php/7.0/cli/conf.d/20-libevent.ini सुडो सेवा php7.0-fpm पुनः आरंभ  < / प्री>

Comments

Post a Comment

Popular posts from this blog

Verilog Error: output or inout port "Q" must be connected to a structural net expression -

I get the error every time, I try to compile. I'm not sure why anyone can help is? I'm new to verilog. Module D_FF (clerk, d, reset_n, q); Input D, Clack, reset_en; Output Q; reg Q; lab4_gdl f1 (.lk (~ clk), d (d), .q.m (qm)); lab4_GDL f2 (.Clk (Clk), D (QM), .Q (Q)); Always start at @ (posedge clk, neggeous reset_n) (Reset_n == 0) Q & lt; = 0; Other questions & lt; = D; Edit End: The problem is what we are asking to do: In this section, you apply the memory / registration circuit on the AlterEdie 2 board. will do. The circuit has the following specifications: The present value of swift SW15-0 on the D2 board should be shown in four hexadecimal four sections of HEX3-0. This part of the circuit will be combination logic. To use an active-less asynchronous reset and KEY1 to use KEY0 as the clock input, you must store SW15-0in in a 16-bit register in the value The register should be enabled to have a 16-bit positive edge, which uses the embedded D flip-flo
Read more

jasper reports - How to center align barcode using jasperreports and barcode4j -

I use iReport 5.5.0 . How to align a barcode component to the center The relevant piece of my jrxml is below & Lt; JR: Code 128 xmlns: JR = "http://jasperreports.sourceforge.net/jasperreports/components" xsi: schemaLocation = "http://jasperreports.sourceforge.net/jasperreports/components http: //jasperreports.sourceforge Purge / xsd / components.xsd "textPosition =" bottom "& gt; & Lt; Jr: codeExpression & gt; & Lt; [CDATA [$ F {number}]] & gt; & Lt; / Jr: codeExpression & gt; & Lt; / Jr: Code 128 & gt; & Lt; / componentElement & gt; "Text" itemprop = "text"> Create a style after this, it is called "barcode", like: & lt; Style name = "barcode" fontName = "Helvetica" fONTSIZE = "10" hAlign = "center" valign = "center" /> and set the property of your barcode element to "barcode".
Read more

c# - ASP.NET MVC - Attaching an entity of type 'MODELNAME' failed because another entity of the same type already has the same primary key value -

In brief, the wrapper module is inserted during posting and the status of an entry is changed to 'modified' . Before changing the state, the state is set to 'separate', but calling attachments () causes the same error to be thrown away. I am using EF 6. Model / wrapper class public class avi model {public A is a {get; Set; } Public listing & lt; B & gt; B {received; Set; } Public cc {receipt; Set; }} Administrator edit public functioning (int? id) {if (id == null) {new HttpStatusCodeResult (HttpStatusCode.BadRequest); } If (! Conveyor Access (id.Value)) new HTTPTitus code result (HTTP status code. Forbidden); Var aViewModel = new AViewModel (); aViewModel.A = db.As.Find (id); If (aViewModel.Receipt == zero) {return HttpNotFound (); } aViewModel.b = db.Bs.Where (x => x.aid == id.Value) .Oolist (); AViewModel.Vendor = db.Cs.Where (x => x.cid == aViewModel.a.cID) .FirstOrDefault (); See Return (aViewModel); } [HTPFost] [Valid AntitiferousTeacon
Read more