sas - Syserr macro variable incorrectly zero? -


I have the following code: 

  data is required; Set & amp; dsetlist.; Run; % Placed SYSERROR: & amp; syserr.; Macro Variable is a list of the descriptor dataset sequences, which, among other things, specifies the length of specific variables to stop the trickle when the ideas are stacked together.  
 If I specify this length incorrectly, then I will get a warning: Multiple lengths were specified ...  
 I hope to see the following in my logs Will:  
  want the data; Has has1 has2 ... haven; Run; Warning: Multiple lengths were specified ... Note: View 1 is used Note: View 2 is used ... Note: See Haven used SYSERROR: 4   
 However, Unfortunately, SYSERROR is instead of 0, despite the warnings.  
 My only idea is that maybe every use scene is being overwritten by Cicero, and the last scene like syserror = 0 has gone without errors or warnings? If this is the case, how can I fix it?  
 -  
 Edit: Replicable  
  Data is 1; Stacked = "y"; Run; The data is 2; Stacked = "no"; Run; Data View 1 / View = View 1; Length $ 1 stacked; Set 1; Run; Data view 2 / view = scene 2; Length $ 1 stacked; Set 2; Run; Want data; Scene 1 Set 2 Scene; Run; % Placed SYSERROR: & amp; syserr.;   
 If I generate an error in transcription, then c / p can not be.  
 If I want  
  data; Length $ 1 stacked; Set 1 is 2; Run; % Placed SYSERROR: & amp; syserr.;   
 This is what I really expect, but seeing the length of the actual assumption is more complete than changing, it is not ideal. Apart from this, it is not entirely amazed that there is no error with Data Segment; Instead the transaction is happening within the scene ... but after seeing the manifest manifestation, syserr does not look like this, possibly because it has not yet been executed at that point. See the  VARLENCHK  option in 
 class = "post-text" itemprop = "text"> 
  option varlenchk = error    Try setting on> Code> - You can turn on  SYSERR  to flag that you want to do this.

Comments

Post a Comment

Popular posts from this blog

Verilog Error: output or inout port "Q" must be connected to a structural net expression -

I get the error every time, I try to compile. I'm not sure why anyone can help is? I'm new to verilog. Module D_FF (clerk, d, reset_n, q); Input D, Clack, reset_en; Output Q; reg Q; lab4_gdl f1 (.lk (~ clk), d (d), .q.m (qm)); lab4_GDL f2 (.Clk (Clk), D (QM), .Q (Q)); Always start at @ (posedge clk, neggeous reset_n) (Reset_n == 0) Q & lt; = 0; Other questions & lt; = D; Edit End: The problem is what we are asking to do: In this section, you apply the memory / registration circuit on the AlterEdie 2 board. will do. The circuit has the following specifications: The present value of swift SW15-0 on the D2 board should be shown in four hexadecimal four sections of HEX3-0. This part of the circuit will be combination logic. To use an active-less asynchronous reset and KEY1 to use KEY0 as the clock input, you must store SW15-0in in a 16-bit register in the value The register should be enabled to have a 16-bit positive edge, which uses the embedded D flip-flo
Read more

jasper reports - How to center align barcode using jasperreports and barcode4j -

I use iReport 5.5.0 . How to align a barcode component to the center The relevant piece of my jrxml is below & Lt; JR: Code 128 xmlns: JR = "http://jasperreports.sourceforge.net/jasperreports/components" xsi: schemaLocation = "http://jasperreports.sourceforge.net/jasperreports/components http: //jasperreports.sourceforge Purge / xsd / components.xsd "textPosition =" bottom "& gt; & Lt; Jr: codeExpression & gt; & Lt; [CDATA [$ F {number}]] & gt; & Lt; / Jr: codeExpression & gt; & Lt; / Jr: Code 128 & gt; & Lt; / componentElement & gt; "Text" itemprop = "text"> Create a style after this, it is called "barcode", like: & lt; Style name = "barcode" fontName = "Helvetica" fONTSIZE = "10" hAlign = "center" valign = "center" /> and set the property of your barcode element to "barcode".
Read more

c# - ASP.NET MVC - Attaching an entity of type 'MODELNAME' failed because another entity of the same type already has the same primary key value -

In brief, the wrapper module is inserted during posting and the status of an entry is changed to 'modified' . Before changing the state, the state is set to 'separate', but calling attachments () causes the same error to be thrown away. I am using EF 6. Model / wrapper class public class avi model {public A is a {get; Set; } Public listing & lt; B & gt; B {received; Set; } Public cc {receipt; Set; }} Administrator edit public functioning (int? id) {if (id == null) {new HttpStatusCodeResult (HttpStatusCode.BadRequest); } If (! Conveyor Access (id.Value)) new HTTPTitus code result (HTTP status code. Forbidden); Var aViewModel = new AViewModel (); aViewModel.A = db.As.Find (id); If (aViewModel.Receipt == zero) {return HttpNotFound (); } aViewModel.b = db.Bs.Where (x => x.aid == id.Value) .Oolist (); AViewModel.Vendor = db.Cs.Where (x => x.cid == aViewModel.a.cID) .FirstOrDefault (); See Return (aViewModel); } [HTPFost] [Valid AntitiferousTeacon
Read more