Gulp Refresh Wordpress PHP files -


In my WordPress environment I have a basic puppy. JS Setup is everything I want to do in addition to how I am reloaded .php files changed works when when the work of GLP is over, this work is being loaded twice, which means That this will start the work and again the task will be gone again. The files I was seeing in the fiction are located in the root directory as well as in the library directory. Apart from this, there is a way to see the chatter is the only change files. I have set it up like this: 

  // PHP Task gulp.task (â "??? phpâ ????, function () {clock {{glob: ['php' , 'Library / .php']}) .pipe (plugins.livereload (server)) .pipe (plugins.notify ({message: a 'ppp work done'}})}} // clock gulp. Listen to the task (â "??? watchâ ????, function () {// port 35729   
 ====================================  
 Here is the result of a single save.  
  [gulp] index.php Was loaded in. A ?? reload / Users / Jeffing / Sites / Forbes / WipeContents / Themes / JointsWP- CSS-Master / Index.php One ?? | One ?? | Reload / User / Jeffing / Sites / Jurbo / Wi-P-content /themes/JointsWP-CSS-master/index.php A ?? | A ?? | reload / user / jfearing / sites / zurb / wp-content / themes / jointsWP-CSS- master / index.php one ?? | One ?? | Reload / Users / Jeffing / Sites / Zabar / WP-Content / Themes / Joints YP-CSS-Master / Index.FPAP | | [GLUP] Index.FPP was reloaded. One ?? | Reload / Users / Jeffing / Sites / Forbes / Wipe-Content / Themes / JointsWP- CSS-Master / Index.fip A ?? | One ?? | Reload / User / Jeffing / Sites / Jurrob / Wi-P-Content /themes/JointsWP-CSS-master/index.php A ?? | One ?? | Reload / user / jfearing / sites / zurb / wp-content / themes / joints wp-css-master / index.php one ?? |    
 
 
 Instead of:  
 
  // default function gulp.task (a "default", ['php', 'watch']);    
 You can try:  
  // default function gulp.task ('default', ['php'], Function) {gulp.start ('clock');});   
 But I can not test it at this time.  
 Full snippet:  
  'Strictly use'; / * Global SIP, Clock, Plugins, Server, Console * / // PHP TASK gulp.task ('php', function (see) {clock {{glob: ['php', 'library / .php']}) .pipe (plugins.livereload (server)) .pipe (plugins.notify ({message: 'php function complete'})}} // clock gulp.task ('watch', function () {// port 35729 Listen   
 If this snippet is not working Should, or when the save time is more than one, then edit it Try to delete:  
  gulp.task ('php'      
 Em> Note: The first two lines in the full snippet are just jshint, so I can prove the code, while I can not execute it without the local php-library.

Comments

Post a Comment

Popular posts from this blog

Verilog Error: output or inout port "Q" must be connected to a structural net expression -

I get the error every time, I try to compile. I'm not sure why anyone can help is? I'm new to verilog. Module D_FF (clerk, d, reset_n, q); Input D, Clack, reset_en; Output Q; reg Q; lab4_gdl f1 (.lk (~ clk), d (d), .q.m (qm)); lab4_GDL f2 (.Clk (Clk), D (QM), .Q (Q)); Always start at @ (posedge clk, neggeous reset_n) (Reset_n == 0) Q & lt; = 0; Other questions & lt; = D; Edit End: The problem is what we are asking to do: In this section, you apply the memory / registration circuit on the AlterEdie 2 board. will do. The circuit has the following specifications: The present value of swift SW15-0 on the D2 board should be shown in four hexadecimal four sections of HEX3-0. This part of the circuit will be combination logic. To use an active-less asynchronous reset and KEY1 to use KEY0 as the clock input, you must store SW15-0in in a 16-bit register in the value The register should be enabled to have a 16-bit positive edge, which uses the embedded D flip-flo
Read more

jasper reports - How to center align barcode using jasperreports and barcode4j -

I use iReport 5.5.0 . How to align a barcode component to the center The relevant piece of my jrxml is below & Lt; JR: Code 128 xmlns: JR = "http://jasperreports.sourceforge.net/jasperreports/components" xsi: schemaLocation = "http://jasperreports.sourceforge.net/jasperreports/components http: //jasperreports.sourceforge Purge / xsd / components.xsd "textPosition =" bottom "& gt; & Lt; Jr: codeExpression & gt; & Lt; [CDATA [$ F {number}]] & gt; & Lt; / Jr: codeExpression & gt; & Lt; / Jr: Code 128 & gt; & Lt; / componentElement & gt; "Text" itemprop = "text"> Create a style after this, it is called "barcode", like: & lt; Style name = "barcode" fontName = "Helvetica" fONTSIZE = "10" hAlign = "center" valign = "center" /> and set the property of your barcode element to "barcode".
Read more

c# - ASP.NET MVC - Attaching an entity of type 'MODELNAME' failed because another entity of the same type already has the same primary key value -

In brief, the wrapper module is inserted during posting and the status of an entry is changed to 'modified' . Before changing the state, the state is set to 'separate', but calling attachments () causes the same error to be thrown away. I am using EF 6. Model / wrapper class public class avi model {public A is a {get; Set; } Public listing & lt; B & gt; B {received; Set; } Public cc {receipt; Set; }} Administrator edit public functioning (int? id) {if (id == null) {new HttpStatusCodeResult (HttpStatusCode.BadRequest); } If (! Conveyor Access (id.Value)) new HTTPTitus code result (HTTP status code. Forbidden); Var aViewModel = new AViewModel (); aViewModel.A = db.As.Find (id); If (aViewModel.Receipt == zero) {return HttpNotFound (); } aViewModel.b = db.Bs.Where (x => x.aid == id.Value) .Oolist (); AViewModel.Vendor = db.Cs.Where (x => x.cid == aViewModel.a.cID) .FirstOrDefault (); See Return (aViewModel); } [HTPFost] [Valid AntitiferousTeacon
Read more