sql server - Parse single column result set into multiple columns SQL -


I have written a stored procedure which is returning the 2 columns temporary table, an ID column that is not unique, but value 2 And at group values ​​between 12 The other column is that the actual data value column I want to break 1 table table into table in basically 11 columns for each dataset in 1 column.

Enter the image details here

Let me call this by ID Has been parsed in. An identity column is not required because they will be unique to their columns. Something like this; Data 2 Data 3 Data 4 102692 ... 103516 .... 108408 .... 104114 ... 103476 .... 108890 ....

And so on, I have tried to use a loop through datasets, but this is mainly being included in 1 inclusion which is bothering me, I do not understand how to say 

  while recordcount & gt; Start at 0tempTable (value1ID2, value1ID3, Value1ID4) and then loop through value2ID2, value2ID3 etc.  
 If this is not available then it is okay you have to find an alternative solution, but the main reason I am trying to do this is for a report builder dataset for a line bitt which is finally a date Will share the clan.   
 
 
 Since you need to collect string values, then you either have to type  max  Or  min  will need to use the total function The problem with it is that it will return a line for each column. To run multiple rows again, you can use the windowing function such as  row_number ()  to generate a unique value for each  id  /  string  Combination will allow you to return several rows for each  id :  
  Data2 = [2], data 3 = [3], Data from 4 = [4] seicate (segmented id order by stringvalue) more than id (string value), row_number () from its sitekake ID ([2], [3], [4]) Switch to D Pivot (Max (string value for the ID)) PIV

Comments

Post a Comment

Popular posts from this blog

Verilog Error: output or inout port "Q" must be connected to a structural net expression -

I get the error every time, I try to compile. I'm not sure why anyone can help is? I'm new to verilog. Module D_FF (clerk, d, reset_n, q); Input D, Clack, reset_en; Output Q; reg Q; lab4_gdl f1 (.lk (~ clk), d (d), .q.m (qm)); lab4_GDL f2 (.Clk (Clk), D (QM), .Q (Q)); Always start at @ (posedge clk, neggeous reset_n) (Reset_n == 0) Q & lt; = 0; Other questions & lt; = D; Edit End: The problem is what we are asking to do: In this section, you apply the memory / registration circuit on the AlterEdie 2 board. will do. The circuit has the following specifications: The present value of swift SW15-0 on the D2 board should be shown in four hexadecimal four sections of HEX3-0. This part of the circuit will be combination logic. To use an active-less asynchronous reset and KEY1 to use KEY0 as the clock input, you must store SW15-0in in a 16-bit register in the value The register should be enabled to have a 16-bit positive edge, which uses the embedded D flip-flo
Read more

jasper reports - How to center align barcode using jasperreports and barcode4j -

I use iReport 5.5.0 . How to align a barcode component to the center The relevant piece of my jrxml is below & Lt; JR: Code 128 xmlns: JR = "http://jasperreports.sourceforge.net/jasperreports/components" xsi: schemaLocation = "http://jasperreports.sourceforge.net/jasperreports/components http: //jasperreports.sourceforge Purge / xsd / components.xsd "textPosition =" bottom "& gt; & Lt; Jr: codeExpression & gt; & Lt; [CDATA [$ F {number}]] & gt; & Lt; / Jr: codeExpression & gt; & Lt; / Jr: Code 128 & gt; & Lt; / componentElement & gt; "Text" itemprop = "text"> Create a style after this, it is called "barcode", like: & lt; Style name = "barcode" fontName = "Helvetica" fONTSIZE = "10" hAlign = "center" valign = "center" /> and set the property of your barcode element to "barcode".
Read more

c# - ASP.NET MVC - Attaching an entity of type 'MODELNAME' failed because another entity of the same type already has the same primary key value -

In brief, the wrapper module is inserted during posting and the status of an entry is changed to 'modified' . Before changing the state, the state is set to 'separate', but calling attachments () causes the same error to be thrown away. I am using EF 6. Model / wrapper class public class avi model {public A is a {get; Set; } Public listing & lt; B & gt; B {received; Set; } Public cc {receipt; Set; }} Administrator edit public functioning (int? id) {if (id == null) {new HttpStatusCodeResult (HttpStatusCode.BadRequest); } If (! Conveyor Access (id.Value)) new HTTPTitus code result (HTTP status code. Forbidden); Var aViewModel = new AViewModel (); aViewModel.A = db.As.Find (id); If (aViewModel.Receipt == zero) {return HttpNotFound (); } aViewModel.b = db.Bs.Where (x => x.aid == id.Value) .Oolist (); AViewModel.Vendor = db.Cs.Where (x => x.cid == aViewModel.a.cID) .FirstOrDefault (); See Return (aViewModel); } [HTPFost] [Valid AntitiferousTeacon
Read more