syntax - How to get numbering to flow properly in Table of Contents -


Can anyone tell me why the following code is not a correct number? I am following the instructions, although the numbering does not continue to the previous 1. I am very new to coding, so any help would be greatly appreciated! 

  & lt; ol class = "inhoudsopgave" & gt; & Lt; li class = "inhoudsopgave" & gt; & Lt; A href = "#" & gt; & Lt; / A & gt; & Lt; / li & gt; & Lt; ol class = "inhoudsopgave" & gt; & Lt; li class = "inhoudsopgave" & gt; & Lt; a href = "# & lt; / a & gt;  ol class =" inhoudsopgave "> 
  •   
     
     
     In short, your list is a mess. You nest your OS inside the OLS Are hunting. If you want to create a list with sub-lists, then archeology should look like this.  
      & lt; ol class = "inhoudsopgave" & gt; & Lt; li class = "inhoudspeag" & gt; & Lt; A href = "#" & gt; & Lt; / A & gt; & Lt; Ol class = "inhoudsopgave" & gt; & Lt; li class = "inhoudsopgave" & gt; & Lt; A href = "#" & gt; & Lt; / A & gt; & Lt; / li & gt; & Lt; Li class = "inhoudsopgave" & gt; & Lt; A href = "#" & gt; & Lt; / A & gt; & Lt; / li & gt; & Lt; Li class = "inhoudsopgave" & gt; & Lt; A href = "#" & gt; & Lt; / A & gt; & Lt; / li & gt; & Lt; Li class = "inhoudsopgave" & gt; & Lt; A href = "#" & gt; & Lt; / A & gt; & Lt; / li & gt; & Lt; / ol & gt; & Lt; / li & gt; & Lt; li class = "inhoudspeag" & gt; & Lt; A href = "#" & gt; & Lt; / A & gt; & Lt; Ol class = "inhoudsopgave" & gt; & Lt; Li class = "inhoudsopgave" & gt; & Lt; A href = "#" & gt; & Lt; / A & gt; & Lt; / li & gt; & Lt; Li class = "inhoudsopgave" & gt; & Lt; A href = "#" & gt; & Lt; / A & gt; & Lt; / li & gt; & Lt; Li class = "inhoudsopgave" & gt; & Lt; A href = "#" & gt; & Lt; / A & gt; & Lt; / li & gt; & Lt; Li class = "inhoudsopgave" & gt; & Lt; A href = "#" & gt; & Lt; / A & gt; & Lt; / li & gt; & Lt; / ol & gt; & Lt; / li & gt; & Lt; / ol & gt;

    • Comments

    Post a Comment

    Popular posts from this blog

    Verilog Error: output or inout port "Q" must be connected to a structural net expression -

    I get the error every time, I try to compile. I'm not sure why anyone can help is? I'm new to verilog. Module D_FF (clerk, d, reset_n, q); Input D, Clack, reset_en; Output Q; reg Q; lab4_gdl f1 (.lk (~ clk), d (d), .q.m (qm)); lab4_GDL f2 (.Clk (Clk), D (QM), .Q (Q)); Always start at @ (posedge clk, neggeous reset_n) (Reset_n == 0) Q & lt; = 0; Other questions & lt; = D; Edit End: The problem is what we are asking to do: In this section, you apply the memory / registration circuit on the AlterEdie 2 board. will do. The circuit has the following specifications: The present value of swift SW15-0 on the D2 board should be shown in four hexadecimal four sections of HEX3-0. This part of the circuit will be combination logic. To use an active-less asynchronous reset and KEY1 to use KEY0 as the clock input, you must store SW15-0in in a 16-bit register in the value The register should be enabled to have a 16-bit positive edge, which uses the embedded D flip-flo
    Read more

    jasper reports - How to center align barcode using jasperreports and barcode4j -

    I use iReport 5.5.0 . How to align a barcode component to the center The relevant piece of my jrxml is below & Lt; JR: Code 128 xmlns: JR = "http://jasperreports.sourceforge.net/jasperreports/components" xsi: schemaLocation = "http://jasperreports.sourceforge.net/jasperreports/components http: //jasperreports.sourceforge Purge / xsd / components.xsd "textPosition =" bottom "& gt; & Lt; Jr: codeExpression & gt; & Lt; [CDATA [$ F {number}]] & gt; & Lt; / Jr: codeExpression & gt; & Lt; / Jr: Code 128 & gt; & Lt; / componentElement & gt; "Text" itemprop = "text"> Create a style after this, it is called "barcode", like: & lt; Style name = "barcode" fontName = "Helvetica" fONTSIZE = "10" hAlign = "center" valign = "center" /> and set the property of your barcode element to "barcode".
    Read more

    c# - ASP.NET MVC - Attaching an entity of type 'MODELNAME' failed because another entity of the same type already has the same primary key value -

    In brief, the wrapper module is inserted during posting and the status of an entry is changed to 'modified' . Before changing the state, the state is set to 'separate', but calling attachments () causes the same error to be thrown away. I am using EF 6. Model / wrapper class public class avi model {public A is a {get; Set; } Public listing & lt; B & gt; B {received; Set; } Public cc {receipt; Set; }} Administrator edit public functioning (int? id) {if (id == null) {new HttpStatusCodeResult (HttpStatusCode.BadRequest); } If (! Conveyor Access (id.Value)) new HTTPTitus code result (HTTP status code. Forbidden); Var aViewModel = new AViewModel (); aViewModel.A = db.As.Find (id); If (aViewModel.Receipt == zero) {return HttpNotFound (); } aViewModel.b = db.Bs.Where (x => x.aid == id.Value) .Oolist (); AViewModel.Vendor = db.Cs.Where (x => x.cid == aViewModel.a.cID) .FirstOrDefault (); See Return (aViewModel); } [HTPFost] [Valid AntitiferousTeacon
    Read more