dependencies - Removing maven dependancies of child pom from parent pom -


My parents are Pom A with POM, B, C and D with children in I, B, C and D, I have dependency with the same type

i.e. parent 

  & lt; artifactID & gt; Blah & lt; / ArtifactID & gt; & Lt; Module & gt; & Lt; Module & gt; B & lt; / Module & gt; & Lt; Module & gt; C & lt; / Module & gt; & Lt; Module & gt; D & lt; / Module & gt; & Lt; / Module & gt;   
 Kid POM  
  & gt; Dependency & gt; & Lt; Dependency & gt; . . & Lt; Scope & gt; Trial & lt; / Scope & gt; & Lt; Type & gt; Test-jar & lt; / Type & gt; & Lt; / Dependencies & gt; & Lt; / Dependencies & gt;   
 So far I have tried to make the plug-in accurate and that does not work when trying to exclude the test scope for child poms.  
 My question is to exclude all dependencies with type paste-jars for all children is a way to add a profile to parent palm thanks   
 
 
 Since you are trying to update the path in the  test  field, you can hook  maven-surfire- plugin  which is actually responsible for creating test roompaths and removing unwanted dependencies or adding new ones. Therefore, if you want to  apply this restriction to each module  you can enter the child for poms, eg For  B :  
  & lt; Project & gt; ... & lt; ArtifactId & gt; B & lt; / ArtifactId> ... & lt; Build & gt; & Lt; Plugins & gt; & Lt; Plugin & gt; & Lt; Group & gt; Org.apache.maven.plugins & lt; / Group & gt; & Lt; ArtifactId & gt; Maven- Perfect-plugin & lt; / ArtifactId> & Lt; Version & gt; 2.17 & lt; / Edition & gt; & Lt; Configuration & gt; & Lt; classpathDependencyExcludes & gt; & Lt; classpathDependencyExclude & gt; $ {Unwanted-Dependency-Group}: $ {Unwanted-dependency-artifactId} & lt; / classpathDependencyExclude & gt; & Lt; / classpathDependencyExcludes & gt; & Lt; / Configuration & gt; & Lt; / Plugin & gt; & Lt; / Plugins & gt; & Lt; / Create & gt; ... & lt; / Project & gt;   
 Or if you want to get this restriction  inherited by all the child modules , then define a profile based plugin in parent palm: < / P> 
  & lt; Project & gt; ... & lt; ArtifactId & gt; A & lt; / ArtifactId> & Lt; Module & gt; B & lt; / Module & gt; & Lt; Module & gt; C & lt; / Module & gt; & Lt; Module & gt; D & lt; / Module & gt; ... & lt; Profile & gt; & Lt; Profile & gt; & Lt; ID & gt; Custom Test Goal & lt; / Id & gt; & Lt; Construction & gt; & Lt; Plugins & gt; & Lt; Plugin & gt; & Lt; Group & gt; Org.apache.maven.plugins & lt; / Group & gt; & Lt; ArtifactId & gt; Maven- Perfect-plugin & lt; / ArtifactId> & Lt; Version & gt; 2.17 & lt; / Edition & gt; & Lt; Configuration & gt; & Lt; classpathDependencyExcludes & gt; & Lt; classpathDependencyExclude & gt; $ {Unwanted-Dependency-Group}: $ {Unwanted-dependency-artifactId} & lt; / classpathDependencyExclude & gt; & Lt; / classpathDependencyExcludes & gt; & Lt; / Configuration & gt; & Lt; / Plugin & gt; & Lt; / Plugins & gt; & Lt; / Create & gt; & Lt; / Profile & gt; & Lt; / Profile & gt; ... & lt; / Project & gt;

Comments

Post a Comment

Popular posts from this blog

Verilog Error: output or inout port "Q" must be connected to a structural net expression -

I get the error every time, I try to compile. I'm not sure why anyone can help is? I'm new to verilog. Module D_FF (clerk, d, reset_n, q); Input D, Clack, reset_en; Output Q; reg Q; lab4_gdl f1 (.lk (~ clk), d (d), .q.m (qm)); lab4_GDL f2 (.Clk (Clk), D (QM), .Q (Q)); Always start at @ (posedge clk, neggeous reset_n) (Reset_n == 0) Q & lt; = 0; Other questions & lt; = D; Edit End: The problem is what we are asking to do: In this section, you apply the memory / registration circuit on the AlterEdie 2 board. will do. The circuit has the following specifications: The present value of swift SW15-0 on the D2 board should be shown in four hexadecimal four sections of HEX3-0. This part of the circuit will be combination logic. To use an active-less asynchronous reset and KEY1 to use KEY0 as the clock input, you must store SW15-0in in a 16-bit register in the value The register should be enabled to have a 16-bit positive edge, which uses the embedded D flip-flo
Read more

jasper reports - How to center align barcode using jasperreports and barcode4j -

I use iReport 5.5.0 . How to align a barcode component to the center The relevant piece of my jrxml is below & Lt; JR: Code 128 xmlns: JR = "http://jasperreports.sourceforge.net/jasperreports/components" xsi: schemaLocation = "http://jasperreports.sourceforge.net/jasperreports/components http: //jasperreports.sourceforge Purge / xsd / components.xsd "textPosition =" bottom "& gt; & Lt; Jr: codeExpression & gt; & Lt; [CDATA [$ F {number}]] & gt; & Lt; / Jr: codeExpression & gt; & Lt; / Jr: Code 128 & gt; & Lt; / componentElement & gt; "Text" itemprop = "text"> Create a style after this, it is called "barcode", like: & lt; Style name = "barcode" fontName = "Helvetica" fONTSIZE = "10" hAlign = "center" valign = "center" /> and set the property of your barcode element to "barcode".
Read more

c# - ASP.NET MVC - Attaching an entity of type 'MODELNAME' failed because another entity of the same type already has the same primary key value -

In brief, the wrapper module is inserted during posting and the status of an entry is changed to 'modified' . Before changing the state, the state is set to 'separate', but calling attachments () causes the same error to be thrown away. I am using EF 6. Model / wrapper class public class avi model {public A is a {get; Set; } Public listing & lt; B & gt; B {received; Set; } Public cc {receipt; Set; }} Administrator edit public functioning (int? id) {if (id == null) {new HttpStatusCodeResult (HttpStatusCode.BadRequest); } If (! Conveyor Access (id.Value)) new HTTPTitus code result (HTTP status code. Forbidden); Var aViewModel = new AViewModel (); aViewModel.A = db.As.Find (id); If (aViewModel.Receipt == zero) {return HttpNotFound (); } aViewModel.b = db.Bs.Where (x => x.aid == id.Value) .Oolist (); AViewModel.Vendor = db.Cs.Where (x => x.cid == aViewModel.a.cID) .FirstOrDefault (); See Return (aViewModel); } [HTPFost] [Valid AntitiferousTeacon
Read more