android - How do I pause/disable and then unpause/reenable AlarmManager from settings page? -


My AlarmManager Utility. In the Java page I am creating an alarm, using this method: 

  Escale Alarm to make public static void (reference this contact, int integration entry ID, long LNGLlight time) {Alarm Manager AM = (alarm manager) thisContext.getSystemService (context .ALARM_SERVICE); Intention this isnt = new intent (this contact, alarm receiver class); ThisIntent.setAction ("StartSingleAlarm"); Intent it Input Extra ("Director EntryID", IntDiInterIDIDID); Pending this reversible = pendingIntent.getBroadcast (this contact, intiIRIIDID, this instant, 0); am.set (alarm manager .rtc_wekup, lnállamtime, hepadding event); }   
 So I have a bunch of people for different days and times. What I want to do is allow the user to close the alarm and "toggle" from the preferences page. Is there any way of doing it? I want to do something like this:  
  public static zero-free onflowarm (reference to this reference) {AlarmManager am = (AlarmManager) thisContext.getSystemService (Context.ALARM_SERVICE); Am.disable (thisContext); }   
 and this:  
  public static zero-free online (reference thisContext) {AlarmManager am = (AlarmManager) thisContext.getSystemService (context.ALARM_SERVICE); Am.enable (thisContext); }   
 
 
 You have two options:  
     
  1.  
     The best approach is to cancel all your outstanding events in  cancellation ()   turnOffAllAlarms () , then return them to  turnOnAllAlarms ()  establish.  turnOnAllAlarms ()  The part should not be hard, because you want the code to handle the reboot, "force stop" etc.   
  2.  
     Be sure to check that the alarm is turned off (for example, through a  SharedPreference ) and if they If you are actually locked down, skipping your normal work is less efficient because you wake up the device at these points on time. However, this may be a low code.

Comments

Post a Comment

Popular posts from this blog

Verilog Error: output or inout port "Q" must be connected to a structural net expression -

I get the error every time, I try to compile. I'm not sure why anyone can help is? I'm new to verilog. Module D_FF (clerk, d, reset_n, q); Input D, Clack, reset_en; Output Q; reg Q; lab4_gdl f1 (.lk (~ clk), d (d), .q.m (qm)); lab4_GDL f2 (.Clk (Clk), D (QM), .Q (Q)); Always start at @ (posedge clk, neggeous reset_n) (Reset_n == 0) Q & lt; = 0; Other questions & lt; = D; Edit End: The problem is what we are asking to do: In this section, you apply the memory / registration circuit on the AlterEdie 2 board. will do. The circuit has the following specifications: The present value of swift SW15-0 on the D2 board should be shown in four hexadecimal four sections of HEX3-0. This part of the circuit will be combination logic. To use an active-less asynchronous reset and KEY1 to use KEY0 as the clock input, you must store SW15-0in in a 16-bit register in the value The register should be enabled to have a 16-bit positive edge, which uses the embedded D flip-flo
Read more

jasper reports - How to center align barcode using jasperreports and barcode4j -

I use iReport 5.5.0 . How to align a barcode component to the center The relevant piece of my jrxml is below & Lt; JR: Code 128 xmlns: JR = "http://jasperreports.sourceforge.net/jasperreports/components" xsi: schemaLocation = "http://jasperreports.sourceforge.net/jasperreports/components http: //jasperreports.sourceforge Purge / xsd / components.xsd "textPosition =" bottom "& gt; & Lt; Jr: codeExpression & gt; & Lt; [CDATA [$ F {number}]] & gt; & Lt; / Jr: codeExpression & gt; & Lt; / Jr: Code 128 & gt; & Lt; / componentElement & gt; "Text" itemprop = "text"> Create a style after this, it is called "barcode", like: & lt; Style name = "barcode" fontName = "Helvetica" fONTSIZE = "10" hAlign = "center" valign = "center" /> and set the property of your barcode element to "barcode".
Read more

c# - ASP.NET MVC - Attaching an entity of type 'MODELNAME' failed because another entity of the same type already has the same primary key value -

In brief, the wrapper module is inserted during posting and the status of an entry is changed to 'modified' . Before changing the state, the state is set to 'separate', but calling attachments () causes the same error to be thrown away. I am using EF 6. Model / wrapper class public class avi model {public A is a {get; Set; } Public listing & lt; B & gt; B {received; Set; } Public cc {receipt; Set; }} Administrator edit public functioning (int? id) {if (id == null) {new HttpStatusCodeResult (HttpStatusCode.BadRequest); } If (! Conveyor Access (id.Value)) new HTTPTitus code result (HTTP status code. Forbidden); Var aViewModel = new AViewModel (); aViewModel.A = db.As.Find (id); If (aViewModel.Receipt == zero) {return HttpNotFound (); } aViewModel.b = db.Bs.Where (x => x.aid == id.Value) .Oolist (); AViewModel.Vendor = db.Cs.Where (x => x.cid == aViewModel.a.cID) .FirstOrDefault (); See Return (aViewModel); } [HTPFost] [Valid AntitiferousTeacon
Read more