(Eclipse SDK update error) An error occur while collecting items to be installed -


I have just updated the ADK and I face the same problem (same version of upgrade) as this person I had to do ()

I followed his observations, yet I did not see the dialogs mentioned in step 4 (4). You should see a dialog that says, "This software has already been installed, instead it will be updated." By right clicking 22.6.1 is being installed.)

Instead, I have an error message whose title is

The problem occurred

It says

There is a problem with the installation software. There was an error collecting items to install

and a part of the description is followed, which I do not understand (see below). Can anyone help? Thacks such as

An error occurred while collecting items to establish session context: (profile = profile, step = org.eclipse.equinox.internal.p2.engine.phases. =, Action =). No repositories were found: osgi.bundle, com.android.ide.eclipse.adt, 22.6.2.v201403212031-1085508 No repositories were found: osgi.bundle, com.android.ide.eclipse.adt.package, 22.6.2 .v201403212031-1085508 No repositories were found: osgi.bundle, com.android.ide.eclipse.base, 22.6.2.v201403212031-1085508 No repositories were found: osgi.bundle, com.android ide.eclipse.ddms, 22.6.22.v201403212031-1085508 No repositories were found: osgi.bundle, com.android.ide.eclipse.gldebugger, 22.6.2.v201403212031-1085508 No repositories were found: osgi. bundle, com.android.ide.eclipse.hierarchyviewer, 22.6.2.v201403212031-1085508 No repositories were found: osgi.bundle , com.android.ide.eclipse.traceview, 22.6.2.v201403212031-1085508 No repositories were found: osgi.bundle, overlay.com.android.ide .eclipse.adt.overlay, 22.6.2.v201403212031-1085508 No repositories were found: org.eclipse.update.feature, com.android.ide.eclipse.adt, 22.6.2.v201403212031-1085508 No repository found Conta ining: org.eclipse.update.feature, com.android .ide.eclipse.ddms, 22.6.2.v201403212031-1085508 found in any repository: org.eclipse.update.feature, com.android.ide.eclipse.gldebugger, 22.6.2.v201403212031-1085508 no repositories Found: org.eclipse.update.feature, com.android.ide.eclipse.hierarchyviewer, 22.6.2.v201403212031-1085508 found in any repository: org.eclipse.upda te.feature, com.android.ide.eclipse.traceview, 22.6.2.v201403212031-1085508

According to Jonsav's link, you have to make sure that you uncheck the 'contact all update sites' when you install to search for 'required software' from the Excel install software screen.

Comments

Post a Comment

Popular posts from this blog

Verilog Error: output or inout port "Q" must be connected to a structural net expression -

I get the error every time, I try to compile. I'm not sure why anyone can help is? I'm new to verilog. Module D_FF (clerk, d, reset_n, q); Input D, Clack, reset_en; Output Q; reg Q; lab4_gdl f1 (.lk (~ clk), d (d), .q.m (qm)); lab4_GDL f2 (.Clk (Clk), D (QM), .Q (Q)); Always start at @ (posedge clk, neggeous reset_n) (Reset_n == 0) Q & lt; = 0; Other questions & lt; = D; Edit End: The problem is what we are asking to do: In this section, you apply the memory / registration circuit on the AlterEdie 2 board. will do. The circuit has the following specifications: The present value of swift SW15-0 on the D2 board should be shown in four hexadecimal four sections of HEX3-0. This part of the circuit will be combination logic. To use an active-less asynchronous reset and KEY1 to use KEY0 as the clock input, you must store SW15-0in in a 16-bit register in the value The register should be enabled to have a 16-bit positive edge, which uses the embedded D flip-flo
Read more

jasper reports - How to center align barcode using jasperreports and barcode4j -

I use iReport 5.5.0 . How to align a barcode component to the center The relevant piece of my jrxml is below & Lt; JR: Code 128 xmlns: JR = "http://jasperreports.sourceforge.net/jasperreports/components" xsi: schemaLocation = "http://jasperreports.sourceforge.net/jasperreports/components http: //jasperreports.sourceforge Purge / xsd / components.xsd "textPosition =" bottom "& gt; & Lt; Jr: codeExpression & gt; & Lt; [CDATA [$ F {number}]] & gt; & Lt; / Jr: codeExpression & gt; & Lt; / Jr: Code 128 & gt; & Lt; / componentElement & gt; "Text" itemprop = "text"> Create a style after this, it is called "barcode", like: & lt; Style name = "barcode" fontName = "Helvetica" fONTSIZE = "10" hAlign = "center" valign = "center" /> and set the property of your barcode element to "barcode".
Read more

c# - ASP.NET MVC - Attaching an entity of type 'MODELNAME' failed because another entity of the same type already has the same primary key value -

In brief, the wrapper module is inserted during posting and the status of an entry is changed to 'modified' . Before changing the state, the state is set to 'separate', but calling attachments () causes the same error to be thrown away. I am using EF 6. Model / wrapper class public class avi model {public A is a {get; Set; } Public listing & lt; B & gt; B {received; Set; } Public cc {receipt; Set; }} Administrator edit public functioning (int? id) {if (id == null) {new HttpStatusCodeResult (HttpStatusCode.BadRequest); } If (! Conveyor Access (id.Value)) new HTTPTitus code result (HTTP status code. Forbidden); Var aViewModel = new AViewModel (); aViewModel.A = db.As.Find (id); If (aViewModel.Receipt == zero) {return HttpNotFound (); } aViewModel.b = db.Bs.Where (x => x.aid == id.Value) .Oolist (); AViewModel.Vendor = db.Cs.Where (x => x.cid == aViewModel.a.cID) .FirstOrDefault (); See Return (aViewModel); } [HTPFost] [Valid AntitiferousTeacon
Read more